Autowatch Ghost Immobiliser Installation
The Ghost is the most advanced aftermarket in the UK. immobiliser for the CAN bus. It's subtle, doesn't have LED indications or key fobs and is concealed in the vehicle's wiring.
It also allows the user to temporarily disable the system by using Transport Mode in the event of renting out their vehicle. This guide will walk you through the steps of installing the Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car from key hacking attacks, cloning and relay attacks. The system is linked directly to the ECU of your vehicle and protected by a pin code you select. It's inaccessible to thieves using diagnostic scanners or other modern methods, and is not able to be disabled by cutting circuits.
The system is simple to use, however it is essential to have a professional installation to ensure a smooth and secure connection to your vehicle's ECU. Installers approved by Thatcham can assist you with the installation and programing of your Ghost system. They can also suggest a tracking system or alarm to complete your vehicle's protection package.
To avoid an accidental deployment of airbags or short circuits The installer must first disconnect your battery. After this is completed the installer is able to safely begin work. Hand tools are essential to make precise connections, while a multimeter can be used to check electrical values and safety. Insulation tape and cable tie are essential to protect connections and ensure that wiring is neat. The Ghost Immobiliser user manual will give specific instructions that are tailored to your model.
During the installation process, it's crucial to select a grounding point that's free of any paint or debris. The installer must ensure that the immobiliser's CAN H as well as CAN L wires are connected to the appropriate ports on your vehicle's ECU. Depending on the model, these wires could need to be soldered or plugged into. To ensure a secure and durable connection, it is recommended that you choose a high-quality plug.
Transport Mode can be activated by the customer after the installation is complete. This permits mechanics or valet parking to use the vehicle without knowing the pin code. To accomplish this, the customer must press the service button on the dashboard five times within 2 seconds. After this is done, the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 immobiliser is TASSA certified and is an extremely efficient immobiliser. It's an excellent choice for those who rent their vehicles regularly on platforms such as Turo. Having an immobiliser can also reduce insurance premiums, since it reduces the likelihood of theft.
Getting Started
It's not difficult to come up using an autowatch immobiliser in order to guard your vehicle from theft. It prevents your car from running even when someone copies or steals your key. It's possible due to its advanced technology, which prevents the engine from starting until the right PIN code has been entered.
The device works by connecting to the CAN bus network in your vehicle, allowing it to communicate with the ECU directly. It uses existing buttons on the dashboard and the steering wheel to create a unique sequence only you know which makes it impossible for anyone else to start your vehicle. This is the best way to protect your pride and joy. It will keep its value intact in the event that you decide to sell it.
Installing Ghost's immobiliser is straightforward, but you must follow the directions to avoid electrical issues and system malfunctions. First, you have to locate and determine a constant 12V power source and an appropriate grounding point on the vehicle's chassis. Then, you can start connecting the wires to the immobiliser. Make use of high-quality connectors and soldering techniques for a solid connection. Also, ensure that you cover the connections with heat shrink tubing and insulation tape to protect them from short circuits in electrical power and other problems.
Once the wires are connected, you are able to connect the battery and begin the engine to check whether the immobiliser works. Once everything is working properly you can place it in a safe location beneath the dash or anywhere else in the vehicle. Be sure to hide it securely to ensure that thieves cannot alter it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) which means it is a top-quality deterrent to car burglars. It offers superior protection against key cloning, hacking and relay attacks, and it isn't able to be disabled unless you know the code. The device is also easy to use and is able to be put into the service valet mode to ensure that your vehicle will not be activated when you bring it in for maintenance or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system that is specifically designed to deter theft of vehicles. It communicates with your vehicle's ECU and connects directly to its CAN bus. Ghost Immobiliser doesn't interfere with the factory settings of your car, unlike other aftermarket systems that require the removal of circuit elements.
The system is also unnoticeable by thieves using diagnostic scanners. The system doesn't send or receive radio frequency signals but instead uses CAN data for communication with your ECU. In addition, it doesn't need any modification to your car's existing key fobs.
Enter your disarm sequence (either two or one buttons) and turn on the ignition of your vehicle to use Ghost Immobiliser. The indicator will flash twice to confirm that you've entered the correct code. You can now begin driving your car safely.
Once installed Once installed, the Ghost Immobiliser will protect your car from hacking and key cloning while preserving the value of your pride and joy. If you ever have to hand over your vehicle for service or valet parking The Ghost Immobiliser can be temporarily disabled in Transport Mode.
You'll require a continuous power source (12V) and an earthing point to complete the installation of a Ghost immobiliser. Make sure that both are properly insulated and can be touched. It is also recommended to use cable ties to tie and secure the wires, as this will decrease the chance of tampering by potential thieves. To avoid making mistakes, make sure to double-check these points and mark them using labels or tape. Verify all connections for signs that they're wearing out. Be sure to ensure that all connections are securely in place, and are properly sealed. Also, don't forget test the Ghost Immobiliser after the installation is complete. This will make sure that the unit is functioning correctly and that all connections are secure and insulated. Be sure to correct any problems immediately.
Testing
The Autowatch Ghost immobiliser is an innovative vehicle security system that connects seamlessly with your vehicle's ECU to prevent unauthorised motor starting. Its cutting-edge technology safeguards your car against key cloning, hacking, and other typical tactics thieves employ to steal cars. The Ghost is a perfect complement to existing tracking and alarm systems to provide the best security for your car. The Ghost's unparalleled features, paired with its discreet design makes it a preferred option for both drivers who love cars and security-conscious drivers.
To ensure proper integration of the Ghost Immobiliser, it's important to follow the steps of the installation process. The best way to begin is to consult the vehicle's wiring diagram, which will serve as a guideline for locating and connecting the required wires. The next step is to determine the power and grounding sources. Once what is a ghost immobiliser have located them, you'll need to mark the points so that they are easy to identify when installing. In addition, it is important to use top-quality tools and materials. Hand tools are essential to assist you in making precise connections. A multimeter can verify electrical values, and ensure security. Insulation tape and cable ties can help keep connections neat and tidy. Additionally, a user's manual will provide specific instructions tailored to your Ghost model.
Before you begin installing it is important to test the system by entering the PIN code, then starting the vehicle. This will ensure that the immobiliser is working according to plan, and prevents unauthorised vehicle start-ups. It's recommended to perform this step regularly as part of your routine inspections of the vehicle to ensure the system is operating correctly.
After the installation is completed Once the installation is complete, you can drive your vehicle with confidence. The Ghost will safeguard your vehicle from potential car thieves. It will ensure that no one is able to escape with your car without having the correct PIN code. The Ghost can also be linked with a Thatcham-approved tracker to identify any attempts at tampering or theft that could lead to the location of your vehicle in the event of it being stolen.
The Ghost is compatible with a wide variety of vehicles, including those from the majority of major manufacturers. Monty's Locksmith can assist you in securing your vehicle with this cutting edge device. Contact us today to learn more about our services and installation options. We are a TASSA Registered installer This certification ensures that we follow strict guidelines and procedures when installing our products. This ensures customers, insurance companies, and law enforcement agencies that installations are done safely and correctly.